Make a flower vase that never leaks to 3D print.

A glass tube or jar inside, two colours, a ribbed band.

6 min readGeneratorsUpdated 15 Nov 2026

Open the flower vases generator

White vase with an olive fluted band and dried grasses, on a wooden shelf.

The Flower Vases generator makes a vase for fresh flowers that holds no water itself. A glass test tube or a small jar drops into a socket inside it from the top, and the water stays in the glass - so the vase cannot leak, however it is printed. You measure your glass, and the vase is built round it: a body that narrows at the shoulder, a ribbed band at the foot in a second colour, and a name or a logo on the side if you want one.

Examples

Peach vase with an orange fluted band and a clear glass tube in its neck.
Peach vase with an orange fluted band and a clear glass tube in its neck.
Terracotta vase with Bloom written on its side and white ranunculus.
Terracotta vase with Bloom written on its side and white ranunculus.
Lilac vase with a purple band, a glass tube and dried flowers.
Lilac vase with a purple band, a glass tube and dried flowers.
Studio render of a sage vase with an olive fluted band at the foot.
Studio render of the generator's default piece.

How to make a flower vase

  1. Measure your glass

    The outside of a test tube, a bud glass or a small jar across its widest point, and its height. Its top sits just under the rim of the vase.

  2. Shape the body

    Round, oval or square, the width and height, and how the bottom edge rounds in.

  3. Shape the top

    A soft round shoulder, a straight slope or none, how wide the neck is, and a flat rim or a top that dips into the opening.

  4. Add the band

    Its height and texture. The printer changes filament once, where the band ends.

  5. Put a name on it

    Text or a logo on the front, inlaid in a third colour or raised.

  6. Export and print

    Upright, the band first. Then drop the glass in and fill it with water.

What you can change

Body
Round, oval (50 to 95% deep) or square (corners rounded 0 to 100%); 50 to 160 mm across, 80 to 250 mm tall; foot rounded 0 to 12 mm.
Top
Shoulder round, angled or none, 10 to 80 mm tall; neck 50 to 95% of the body; flat rim or funnel.
Band
15 to 150 mm tall; flutes, ribs, spiral, diamond, waves or plain; texture 0.4 to 3 mm deep, ribs every 3 to 30 mm.
Glass
10 to 110 mm across and 40 to 240 mm tall. A wide-mouth template takes a 75 mm jar.
Name or logo
Text in one of 11 fonts, 6 to 40 mm tall, or your logo (SVG, PNG or JPG) on the side: inlaid flush in a second colour, or raised 1 mm in the body's colour. A word too long for the room is set smaller, with a note.

Tip.Print it upright with the band at the bottom: the shoulder and the textures are kept within 45 degrees, so it needs no supports. Set the colour change at the height the studio shows for the band.

The socket is 0.6 mm wider than your glass on each side. Slide the glass in before the flowers, and lift it out to change the water.

The 3MF keeps each colour as its own object, so a printer with automatic filament changes (such as a Bambu Lab AMS) prints it in one go. With one colour, print every object in the same filament.

Where it is used

  • A bud vase on a desk, a windowsill or a bedside table.
  • Table vases for a wedding or a cafe, with a name or a logo on each.
  • A gift with a name, with a few stems in it.
  • Dried flowers and grasses, with or without the glass.

Questions

Does a 3D printed vase leak?

This one holds no water: the water stays in a glass test tube or jar inside it. That is why it does not leak, even printed in plain PLA.

What glass does it take?

Any glass with straight sides, from a 10 mm test tube to a 110 mm jar. Measure its outside and its height; the socket is built to it.

Is it one piece or two?

One piece in two colours: the body and the band at its foot. The glass drops in from the top, so nothing needs to come apart.

Does it need supports?

No. It prints upright, and every slope - the shoulder, the rounded foot and the band texture - stays within 45 degrees.

Can I put a name or a logo on it?

Yes. Upload an SVG, PNG or JPG; a picture is traced to one colour. Choose an inlay flush with the surface in a second colour, or a raised mark. You must hold the rights to what you upload.

What file do I get?

A 3MF, which keeps each colour as its own object for a multi-colour printer, or an STL. Every file is checked before it downloads: closed (watertight) geometry, a single shell and walls thick enough to print.

Is it free?

The free plan gives 3 designs a month on each generator. Selling the printed pieces needs the Seller or Studio plan, which include the commercial licence.

Licence

On the Free and Maker plans you may print your designs for yourself and as gifts, not for sale. Selling the printed pieces needs the Seller or Studio plan, which include the commercial licence and a licence certificate for each design. Pieces made during the free beta, before paid plans launched, may still be sold on the terms of that time. The exported files themselves can never be resold or redistributed, on any plan.

This is a summary. Read Can I sell rings I 3D print with Morcano? and the Terms, which are the authoritative text.

Keep reading